How To Repair Small Holes In Hardwood Floor

Hardwood Floor Repair: How to Patch a Hardwood Flooring

Updated: Sep. thirty, 2022

How to replace a damaged oak or other hardwood floorboard.

Nosotros'll prove y'all how to supervene upon a damaged hardwood floorboard in just a couple hours using basic carpentry tools. This article covers removing a pigsty-filled or otherwise damaged tongue-and-groove lath, then installing a new 1.

You might too similar: TBD

Time

A full twenty-four hours

Complexity

Beginner

Cost

Less than $20

Replacing Hardwood Floors: Mark the floor lath plank and drill holes

Photo 1: Determine what needs to be removed

With hardwood floor repair, yous need to offset determine what should be removed. Look at the damaged flooring plank and decide how much length to remove. You lot want the new barrel joint to be staggered nigh ten in. from the butt joints of any next flooring courses. Describe a line for the cut, then use a sharp chisel (one in. or wider) to carefully cut the line through the height ane/eight in. of the flooring to create a crisp edge that defines the new butt joint.

With a spade bit, drill iii relief holes side by side to the layout line to remove the bulk of the wood. Complete the cutting by using the chisel to trim the full edge of the butt articulation completely foursquare and clean.

Replacing damaged or hole-filled hardwood tongue-and-groove floorboards takes a couple of hours, sharp tools and an agreement of how to break the interlocking tongue-and-groove board edges. When removing old floor, create a new butt joint on just the side of the plank that'south closest to the hole or where the damage ends.

Using the technique shown in Photos 1 – iv and a carbide-tipped floor blade that can cut through nails, remove the old hardwood floor and install a perfect replacement piece. New flooring usually stands "proud" next to older, worn flooring.

Besides, matching the colour of aged flooring is hard. For these reasons, the all-time time to repair flooring planks is when the entire floor needs to be sanded and refinished. Otherwise, using chugalug and orbital sanders, you'll have to level and so cease the new plank and so it blends into the existing flooring—a tough chore.

Saw relief cuts into the flooring plank

Photo two: Cut into the damaged floorboard

Brand relief cuts in the flooring plank using a circular saw.

Saw two parallel relief cuts an inch apart down the center of the flooring plank to be removed. Set the saw bract depth 1/16 in. deeper than the thickness of the floor. Position the round saw in front of the newly created butt joint with the saw guard retracted, the blade clear of the flooring and the weight of the saw balanced on the front end of the saw shoe. For rubber, don't position any office of your body behind the blade.

Grip the saw firmly, turn information technology on, carefully lower the blade into the flooring, and make the first saw pass downwardly the flooring to just before the other end of the lath. Repeat the procedure with a second plunge cut.

Using the chisel and a pry bar, remove the strip of flooring betwixt the relief cuts and pull the tongue-and-groove edges of the old floor where they interlock with the side by side flooring courses. Completely clean out the opened department of floor.

Replacing Hardwood Floors: Remove the bottom of the groove from the new floor plank

Photograph 3: Set the new plank

Saw off the bottom groove on the new flooring plank.

Rip cutting and remove the bottom groove from the replacement flooring piece using a table saw, circular saw, or sharp chisel and utility knife. Ready the saw fence to cutting v/16 in. off the width of the plank and the saw blade depth to cut into information technology 1/four in. deep. Once the bottom groove has been removed, measure the length required for the replacement piece and cut it. Pencil the location of flooring joists on the new board.

Circumspection:

Our blade guard is removed for the photo—employ yours!

Fit and boom the new floor plank

Photo iv: Set the new plank in place

Install the new floorboard by inserting the natural language into the groove of the adjacent plank.

Install the replacement floor board by inserting the tongue side into the groove of the adjacent flooring plank and dropping the board into position. If necessary, tap the new board flush into position using a safety mallet. Drill pairs of 1/eight-in. blast holes near the ends of the new board and at each joist and fasten the flooring with 8d finish nails. Set the nailheads.

Required Tools for this Project

Accept the necessary tools for this DIY project lined upwards before you start—you'll save time and frustration.

Required Materials for this Project

Avoid last-minute shopping trips past having all your materials fix alee of time. Hither's a list.

Originally Published: September 30, 2022

Similar Projects

Source: https://www.familyhandyman.com/project/patch-a-hardwood-floor/

Share this post