How To Repair The Grips On Ps4 Controllers

The DualShock iv is a fantastic reimagining of the classic PlayStation controller and feels slap-up in the manus, nevertheless, information technology has ane really abrasive design flaw. The rubberized tops of the analog sticks tend to tear themselves apart, especially with prolonged use. This happens because the difficult plastic of the analog sticks pushes upwards into the safe while your thumbs are decorated pushing down, this creates some really horrible tearing of the condom.

Most people will tend to notice the tearing on the left stick every bit that is usually the 1 doing the difficult work. (Movement etc.). I've extensively played Bloodborne and Metal Gear Solid 5, both of which make heavy usage of the left stick. At present my controller looks like it'south been ravaged past some kind of animal and feel even worse. I've recently been playing Monster Hunter World, just I know if I was to use this controller as is, my thumb would exist slipping off the stick all the fourth dimension.

And so, how do yous supercede PS4 analog sticks? The best way to supervene upon PS4 analog sticks is to open the DualShock 4, remove and supplant the damaged sticks. There are options like tertiary political party 'Thumb grips' which can slide on acme (and probably autumn back off due to the degradation of the rubber) but in my opinion, this looks quite tacky and don't experience right.

In this guide, I volition testify you how to open, disassemble the PS4 controller and replace the analog sticks.

For this guide you will demand the following:

1 x Modest Philips caput screwdriver (I used size 1.5)

Replacement analog sticks (I got mine from Amazon)

20 minutes

Optional: Spudger

How to Disassemble Your PS4 controller

Step 1

Turn your DualShock 4 over and we volition demand to remove the iv Philips head screws. These are the just screws property the two halves of the controller together. At present, be careful with these screws, they are fabricated from quite a soft metal. One time the screws are out you can carefully 'separate' open the two halves. I find a spudger can help here to pry open the seam between the peak and the bottom parts of the controller but is non-essential.

The best areas to commencement are either the divide at the bottom of the controller handles or nigh the headphone jack.

Slowly work your way around the controller until it separates. There are clips inside holding everything together and they are pretty hardy so chances of breaking them are slim. Lift the underside of the controller prying dorsum towards the shoulder buttons like below. If you are lucky you will exist able to remove one halve hands, unlike me who knocked off my L2 push, Spring and the reset button!

If you have managed to knock off any buttons, put them bated and we will reassemble them afterward.

At present, be careful when separating as there is a ribbon cable from the primary board going to the controller's low-cal bar!

Also, I was surprised by how much clay and grim had got stuck inside my controller! Now might be a practiced time to clean the controller with some isopropyl alcohol.

Footstep 2

Before we go whatever farther we volition desire to disconnect the bombardment from the main board. Observe the white connector next to the battery and wiggle it upwardly and it should popular out. You will then exist able to remove the battery from the battery housing and fix bated.

Side Notation: Sony decided to but include 1000mAh bombardment inside the DS4. You tin upgrade the battery to have twice the chapters. If you desire to double your controller's battery life you can pick up a higher capacity battery here

With the bombardment removed, we can now remove that ribbon cable! To remove the ribbon cablevision, you can gently pull up on the blue tab. Once that is removed y'all can set the back side of the controller aside.

Adjacent, nosotros motility onto the bombardment housing. Either side of the black battery housing is clipped downward to the PCB. To remove the housing nosotros will need to insert a screwdriver carefully into the little hole and gently push outwards. Practice this on both sides and nosotros will be able to remove the housing.

Step 3

On the elevation corner of the main board, nosotros will find another ribbon cablevision. Pull towards yourself on the white tab to free the ribbon cable. You lot will so exist able to pull up on the ribbon cable to unplug it.

There is one more than Philips head spiral holding the master lath downward. Remove that and set aside. You volition now be able to lift out the PCB. I highly suggest yous continue the residuum of the controller confront down, this is so y'all do not finish up with buttons everywhere. Gravity is your friend here and volition help to go along everything in the right place.

Plough your board over and y'all will at present have access to the analog sticks. To remove the erstwhile sticks, you simply pull upwards on them. Y'all may require a niggling force here.

Once removed you will be able to replace the analog sticks with your replacements. Underneath the sticks you will notice they have an almost rectangular indent, so y'all cannot install these incorrectly. Push the replacements back into place where the originals were. You can test out that L3 & R3 click in at this point. If they do then congratulations, you take successfully replaced your analog sticks.

Stride 4

Put everything back together. Place the PCB dorsum into the controller and secure with the screw removed earlier. Be careful not to over tighten this spiral, yous will naturally roughshod where it wants to stop.

Push back in the ribbon cablevision at the superlative of the controller and close the white tab. Line up and prune in the black battery housing, you lot merely just push down on either side and it will click back into place onto the PCB.

At present, remember the reset button that fell out before? Well, its fourth dimension to put that back into identify. It fits directly into the hold on the battery housing. You should be able to push button it downward and feel a tactile response.

Adjacent upward is the L2 button and leap. This is kind of hard to explain so, here we go! Either side of the L2 button you lot will see a cylindrical tube which the centre part of the spring can slide onto. Once on we can insert the button with spring fastened into place. The spring should naturally sit in a small well in the controller like below.

Side by side, nosotros reinstall the battery by putting it back into the housing and connecting it back to the DualShock 4's main board.

Grab the other half of the controller and plug the ribbon cable back into the main lath. Use the blue tab to get a firm grip on the cable and wiggle it dorsum into place.

Shut the instance dorsum together starting by lining upward the shoulder buttons and push back together. Your controller may get stuck with the posts for the screws in the handles. Just gently push them inwards. With that, everything should exist able to clip back together.

Finally, you can put back the four screws into the dorsum of the controller making sure not to over tighten.

Determination

Replacing the analog sticks in the PS4's DualShock four controller is quite straightforward, will save you having to buy a new controller and doesn't take much time at all. The hardest part is actually getting the shell open and information technology took me a couple of minutes to get the back role of the shell off from the shoulder buttons.

While researching how to take apart my DS4 controller, I found out that the analog sticks tin be switched out with replacement Xbox Ane sticks if you prefer. They accept the same blazon of innards and then tin exist connected without any modification. Personally, I prefer to keep things equally shut to the original every bit possible merely, it's dainty to accept the selection.

Overall, I am very happy with how my controller turned out and I plan to make a video on replacing my second PS4 controller's analog sticks which I will link to this article one time complete.

Source: https://cheapergamer.co.uk/how-to-fix-worn-ps4-controller-analog-sticks/

Posted by: mayonstent1991.blogspot.com

Share this post